ราคาพิเศษ สอบถามโทร 080-6144774 ,02-9810944
QSC CX302 เพาเวอร์แอมป์ เครื่องขยายเสียง
Features
o Eight two-channel models to meet your exact power requirements
o Three 70-volt direct models
o Five low-impedance models; the CX902 and CX1102 also directly drive 70 volt loads
o Exclusive PowerLight switch-mode power supply technology for high performance and compact size
o Custom integrated security cover for tamper proof installations
o Variable speed fan for low noise
o 1-dB detented gain controls for fast and accurate gain settings
o Active inrush limiting eliminates AC inrush current, removing the need for expensive power sequencers
o XLR and detachable Euro style input connectors
o HD15 DataPort connector for Q-Sys and QSControl computer control and monitoring
o Dip switch control for clip limiters, high pass filters, bridge mono and parallel operation
o Selectable high pass filters protect speakers and prevent speaker transformer saturation withminimal effect on program material (33 Hz or 75 Hz on non-V models, 50 Hz or 75 Hz on V models)
o Comprehensive front panel indicators including signal, clip, protect and QSC's exclusive bridge mono and parallel input LEDs
o Barrier strip output connector
o Comprehensive protection circuitry including DC, infrasonic, thermal overload and short circuit protection
o Class H complementary bipolar output circuitry for high efficiency (CX702, CX902, CX1102, and CX1202V)
o Optional external transformer accessory pack for isolated 25-, 70-, and 100-volt outputs (converts CX302 to 400 watts per channel, or 300 watts into 25 V)
o Compact size - all models are only 2 rack units high and 14" deep for reduced rack cost and floor space
o Light weight - all models weigh only 21 pounds (9.5 kg) for easier racking and shipping
o 3-year warranty plus optional 3-year extended service contract
o All CX Series amplifiers meet the European Union's 2006 RoHS directive to restrict the use of hazardous materials used in electronic devices.
o SPECIFICATIONS
|
CX302
|
|
|
POWER PER CHANNEL, STEREO MODE, Both Channels Driven
|
8Ω, 20 Hz–20 kHz, 0.05% THD
|
200 W
|
|
4Ω, 20 Hz–20 kHz, 0.05% THD
|
325 W
|
|
2Ω, 1 kHz, 1% THD
|
600 W
|
|
70V, 20 Hz–20 kHz, 0.05% THD
|
400 W
with IT-42*
|
|
|
POWER, BRIDGED MONO MODE
|
16Ω, 20 Hz–20 kHz, 0.1% THD
|
400 W
|
|
8Ω, 20 Hz–20 kHz, 0.1% THD
|
700 W
|
-
|
-
|
2200 W
|
4Ω, 1 kHz, 1% THD
|
1200 W
|
-
|
-
|
-
|
Noise, 20 Hz–20 kHz
|
-107 dB
|
|
Input Sensitivity @ 8 ohms
|
1.26 Vrms
|
|
Maximum Voltage Gain
|
30 dB
|
|
Output Circuitry Class
|
AB+B
|
|
|
|
Distortion (SMPTE-IM)
|
Less than 0.02%
|
Distortion (Typical)
20 Hz–20 kHz: 10 dB below rated power
1.0 kHz and below: full rated power
|
Less than 0.01% THD
Less than 0.01% THD
|
Frequency Response
|
20 Hz–20 kHz, ±0.2 dB
|
Damping Factor
|
Greater than 500
|
Input Impedance
|
6 kΩ unbalanced, 12 kΩ balanced
|
Input Clipping
|
10 V rms (+22 dBu)
|
Cooling
|
Variable-speed fan, rear-to-front air flow
|
Connectors, each channel
|
Input: 3-pin XLR & 3-pin detachable terminal blocks (1 each per channel)
Output: Safety-shrouded barrier strip
|
Amplifier Protection
|
Full short circuit, open circuit, thermal, ultrasonic, and RF protection.
Stable into reactive or mismatched loads.
|
Load Protection
|
On/off muting, DC-fault power supply shutdown
|
Dimensions
|
19" (48.3 cm) wide, 3.5" (8.9 cm) tall (2 RU),
14" (35.6 cm) deep (from front mounting rails)
|
Weight
|
21 lb (9.5 kg) net
27 lb (12.3 kg) shipping
|
* An isolation transformer (the IT-42) is available for the CX302, which converts its low-impedance outputs to isolated 400 W per channel constant-voltage outputs.
|
|
|
|
|
|
|
|