ราคาพิเศษ สอบถามโทร 080-6144774,02-9810944

JBL KX100 Karaoke Processor

The KX100 is a powerful, full-featured preamp and system processor, designed specifically for karaoke installations. With a variety of audio connectivity options, video I/O for video switching, and dbx® and Lexicon® effects processing used by countless music professionals and singers around the world, the KX100 provides you with all the connectivity and processing required for an amazing karaoke experience.

Features :

Storage for up to 60 Presets (30 Factory Presets and 30 User Presets)

Legendary Lexicon® delay and reverb effects

dbx® processing (feedback elimination, EQ, AGC, limiting, crossover, and microphone exciter)

Pitch processing for altering music material to fit within a vocalist’s range

Dance mode for instant/automatic subwoofer enhancement

3 Microphone preamplifiers

3 Composite video inputs for simultaneous audio/video switching

Built in mixer for blending the levels of the microphones, music, and effects

Record output for recording the audio performance to an external recorder

USB port for use with the KX100 software GUI and firmware updates

IR sensor with included remote control

Specifications :

• MIC Input Type : XLR & ¼” balanced or unbalanced
• Impedance : 600 Ohm
• A/D Conversion : 24 bit, 48 kHz
• EIN : > 113 dB, 20 kHz Bandwidth
• Level Control : 0 to +33 dB
• Line Input Type : RCA unbalanced left & right
• Impedance : 24K Ohm
• XLR Output Type : Balanced or unbalanced
• Level  : + 4 dBu Nominal, +20 dBu Maximum
• Impedance : 30 Ohm balanced, 15 Ohm unbalanced
• Frequency Response : 20 Hz to 20 kHz, +/- 1 dB
• THD+ N : <0.07% 20 Hz – 20 kHz
• Dynamic Range : >103 dB
• DSP Processor : 24 bit
• Computer Connection : USB 2.0
• Power : 9V DC @ 2 A
• Weight : 3.75 lb
• JBL Ki110 10 Inch 3-Way Full Range Loudspeaker System
• The Ki110 is a 3-way full-range speaker designed specially for KTV market needs. The Ki110 utilizes a single 10″ woofer, two 3″ cone midrange drivers, and two 3″ cone tweeters.

Features :

10″ woofer with 2″ voice coil provides high power handling

Linear suspension and vented yoke design for woofer effectively reduces the distortion and power compression

Two 3″ cone midrange drivers and two 3″ cone tweeters for better vocal reproduction

Precision engineered crossover divides and optimizes the three-band frequency response

Enclosure constructed of MDF (Medium Density Fiberboard) with vinyl laminated finish

Built-in protection circuit engineered specifically to protect the tweeter without interrupting performance

Specifications :

•  
• System Type : 10″, 3-way, bass-reflex
• Frequency Range (-10 dB) : 48 Hz - 18 kHz
• Frequency Response (±3 dB) : 65 Hz - 16 KHz
• Sensitivity (1w/1m) : 89 dB
• Nominal Impedance : 8 Ohms
• Maximum SPL :  111 dB (117 dB peak) @ 1m
• Power Rating
• (Continuous/Program/Peak) : 150 W/300 W/600 W
• Recommended amplifier power : 180W - 250W @ 8 ohms
• Coverage Pattern : 150° x 120° (H x V)
• Dimensions (H x W x D) : 290 mm x 506 mm x 320 mm
• 11.4 in x 20 in x 12.6 in
• Net Weight : 12.4 Kg (27.3 lbs)
• LF Driver :  1 x 10″ Woofer
• MF Driver :  2 x 3″ paper cone midrange drivers
• HF Driver :  2 x 3″ paper cone tweeters
• Input Connectors : Binding post
• Enclosure Construction : Vinyl covered 12 mm MDF
• Suspension Attachment : 2 x M10 threaded hardware

Specifications :

• Sensitivity (for full rated power at 4 ohms)
• 1.4 Vrms
• Frequency Response (at 1 watt, 20 Hz - 20 kHz)
• +0 dB, –1 dB
• Signal-to-Noise Ratio
• Rated as dBr to full rated 8Ω power output (A-Weighted): 
• XLS1000 > 97 dB 
• XLS1500, XLS2000, XLS2500 > 103 dB
• Damping Factor (8 ohm): 10 Hz to 400 Hz
• > 200
• Crosstalk (below rated 8Ω power)
• At 1kHz: > 85dB 
• At 20kHz: >55dB
• Input Impedance (nominal)
• 20 kΩ balanced, 10 kΩ unbalanced
• Load Impedance 2 to 8 Ω per channel in Stereo
• 4 to 8 Ω in Bridge Mono
• AC Line Voltage and Frequency Configurations Available (± 10%)
• 120 VAC 60 Hz
• 100 VAC 50/60 Hz
• 220 and 240 VAC 50 Hz 
• Ventilation
• Flow-through ventilation from front to back
• Cooling
• Internal heat sinks with forced-air cooling for rapid, uniform heat dissipation
• Air Volume Requirements (per minute per unit)
• 80.15 ft³ (2.27 m³)
• Integrated Processing
• PureBand™ Crossover System
• Crossover Filter:Linkwitz-Riley 24dB per Octave
• Crossover Frequency Range: 50 HZ - 3 kHz
• Crossover Mode:Crossover (CH1=LPF, CH2=HPF), LowPass (both channels LPF), HighPass (both channels HPF), Bridge (LPF or HPF).
• Peakx™ limiters: Channel independent clip limiter designed to provide maximum output while protecting your loudspeakers
• Input/Output
• Input Connectors: XLR (one per channel), 1/4-Inch (one per channel), and RCA (one per channel). 1/4-Inch connectors can be used as loop-thrus to distribute signal to additional amplifiers.
• Output Connectors: Two 4-Pole Speakon® Output Connectors accept 2-pole or 4-pole Speakon® connectors. The top Speakon connector is wired for both channels so it can be used for bridgemono wiring or for stereo wiring of two speakers to a single Speakon connector.
• One pair of back-panel binding posts per channel; accepts banana plugs or bare wire. (European models do not accept banana plugs.)
• Construction
• XLS1000/XLS1500: 8.12-Inch (20.62cm) depth 
• XLS2000/XLS2500: 10.35-Inch (26.29cm) depth
• Dimensions
• EIA Standard 19-inch (48.3-cm) rack mount width
• (EIA RS-310-B), 3.5-inch (8.9-cm) height.
• XLS 1000/1500: 7.7-inch (19.6-cm) depth.
• XLS 2000/2500: 10.7-inch (27.2-cm) depth.
• Net Weight , Shipping Weight
• XLS1000: 8.6 lb (3.9kg), 13.6 lb (6.2 kg) 
• XLS1500: 8.6 lb (3.9kg), 13.6 lb (6.2 kg) 
• XLS2000: 10.75 lb (4.9kg), 15.8 lb (7.1 kg)
• XLS2500: 10.75 lb (4.9kg), 15.8 lb (7.1 kg)
• SHURE PG58 Vocal Microphone
• A rugged microphone tuned to accentuate the clarity of lead and back-up vocals.

Features :

Tailored frequency response is smooth and extended. Tuned specifically for vocal applications.

Cardioid polar pattern picks up the most sound from in front of the microphone and some sound from the sides. Less susceptible to feedback in high volume settings.

Dynamic cartridge has a simple, rugged coil. Handles extreme volume levels without distortion.

Cartridge includes a neodymium magnet for high output level.

Internal shock mount for reduced handling noise.

Durable metal construction.

On/off switch for onstage control.

Hardened steel mesh ball grille that resists wear and abuse.

Integral "pop" filter reduces explosive breath sounds and wind noise.

Includes 15ft (4.57m) cable, break-resistant mic clip and storage bag.

Replacement cartridge :  RPM150.

Specifications :

• Frequency Response : 60 to 15,000 Hz
• Polar Pattern : Cardioid
• Type : Dynamic (moving coil)